Dr Francisco Vedreno Santos' Outputs (22)

Diagnosis of Rotor Asymmetries in Induction Motors: A Steady State Approach Using Rotating Frame References (2025)
Journal Article
Vedreño Santos, F., Frosini, L., & Moriñigo Sotelo, D. (2025). Diagnosis of Rotor Asymmetries in Induction Motors: A Steady State Approach Using Rotating Frame References. e-Prime - Advances in Electrical Engineering, Electronics and Energy, 12, Article 100957. https://doi.org/10.1016/j.prime.2025.100957

The diagnostic of electrical machines is of paramount importance, particularly with the Motor Current Signature Analysis (MCSA) method. MCSA stands out as a potent and non-intrusive tool for evaluating the condition of electric motors. This paper int... Read More about Diagnosis of Rotor Asymmetries in Induction Motors: A Steady State Approach Using Rotating Frame References.

An innovative approach for the passive cooling of batteries: An empirical investigation of copper deposition on polyurethane foam for the enhancement of phase change material (2024)
Journal Article
Alcock, K. M., Shearer, N., Santos, F. V., Cai, Z., & Goh, K. (2024). An innovative approach for the passive cooling of batteries: An empirical investigation of copper deposition on polyurethane foam for the enhancement of phase change material. Applied Materials Today, 38, Article 102221. https://doi.org/10.1016/j.apmt.2024.102221

A proof-of-concept utilising Copper-Plated Polyurethane Foam (CPPF) and Phase Change Material (PCM) for passive thermal management of lithium-ion batteries is demonstrated in this study. The aim of this research is to assess the effectiveness of CPPF... Read More about An innovative approach for the passive cooling of batteries: An empirical investigation of copper deposition on polyurethane foam for the enhancement of phase change material.

Using Frequency B-Splines for an accurate and faster calculation of adaptive transforms for electric machines diagnosis (2024)
Presentation / Conference Contribution
Pons-Llinares, J., Quijano-López, A., Bonet-Jara, J., & Vedreño-Santos, F. (2024, May). Using Frequency B-Splines for an accurate and faster calculation of adaptive transforms for electric machines diagnosis. Presented at Electrimacs 2024, Castellón de la Plana, Spain

Early detection of faults in electric motors is crucial to prevent unplanned downtime and expensive repairs. Transient analysis through time-frequency transforms reveals important information on the motor condition. Computational time of these transf... Read More about Using Frequency B-Splines for an accurate and faster calculation of adaptive transforms for electric machines diagnosis.

Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Load Variations (2024)
Journal Article
Bonet-Jara, J., Fernandez-Cavero, V., Vedreno-Santos, F., Morinigo-Sotelo, D., & Pons-Llinares, J. (2024). Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Load Variations. IEEE Transactions on Industry Applications, 60(3), 3903-3911. https://doi.org/10.1109/tia.2024.3371393

Induction motors work under steady-state in many applications. Nevertheless, in some cases they experience periodic load fluctuations, which generate constant frequency harmonics close to variable frequency bar breakage harmonics. In these cases, tim... Read More about Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Load Variations.

Individual Cell-Level Temperature Monitoring of a Lithium-Ion Battery Pack (2023)
Journal Article
Alcock, K. M., González-Vila, Á., Beg, M., Vedreño-Santos, F., Cai, Z., Alwis, L. S. M., & Goh, K. (2023). Individual Cell-Level Temperature Monitoring of a Lithium-Ion Battery Pack. Sensors, 23(9), Article 4306. https://doi.org/10.3390/s23094306

The work described herein details the deployment of an optical fibre strand with five fibre Bragg grating (FBG) sensors for individual cell-level temperature monitoring of a three-cell lithium-ion battery pack. A polymer guide tube with 3D printed pl... Read More about Individual Cell-Level Temperature Monitoring of a Lithium-Ion Battery Pack.

Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Arbitrary Load Variations (2022)
Presentation / Conference Contribution
Bonet-Jara, J., Fernandez-Cavero, V., Vedreno Santos, F., & Pons-Llinares, J. (2022, September). Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Arbitrary Load Variations. Presented at 2022 International Conference on Electrical Machines (ICEM), Valencia, Spain

Induction motors work under steady state in many applications. Nevertheless, in some cases (e.g., wood cutting machine or pulp mixer in paper industries), the load continuously varies. In these cases, time-frequency transforms are needed to detect th... Read More about Very Accurate Time-Frequency Representation of Induction Motors Harmonics for Fault Diagnosis Under Arbitrary Load Variations.

Performance of Superconducting Generators with Different Topologies under Fault Conditions (2019)
Presentation / Conference Contribution
Guan, Y., Vedreno Santos, F., Azar, Z., Thomas, A., Li, G., Odavic, M., & Zhu, Z. (2018, April). Performance of Superconducting Generators with Different Topologies under Fault Conditions. Presented at The 9th International Conference on Power Electronics, Machines and Drives (PEMD 2018), Liverpool, UK

This paper compares the short-circuit performance of superconducting (SC) generators with three different topologies, i.e., iron-cored stator and rotor, iron-cored stator and air-cored rotor, and air-cored stator and rotor. The analysis is based on t... Read More about Performance of Superconducting Generators with Different Topologies under Fault Conditions.

Design considerations for high-power converters interfacing 10 MW superconducting wind power generators (2017)
Journal Article
Vedreño Santos, F., Odavic, M., Guan, Y., Azar, Z., Thomas, A., Li, G.-J., & Zhu, Z. (2017). Design considerations for high-power converters interfacing 10 MW superconducting wind power generators. IET Power Electronics, 10(12), 1461-1467. https://doi.org/10.1049/iet-pel.2016.0512

The design of power electronic converters for the integration of wind generated power into the grid is more and more important due to a new class of Superconducting Generators (SG) with power ratings of up to 20 MW. High efficiency of power converter... Read More about Design considerations for high-power converters interfacing 10 MW superconducting wind power generators.

Comparison of Electromagnetic Performance of 10-MW Superconducting Generators With Different Topologies for Offshore Direct-Drive Wind Turbines (2017)
Journal Article
Guan, Y., Zhu, Z. Q., Azar, Z., Thomas, A. S., Vedreño-Santos, F., Li, G.-J., & Odavic, M. (2017). Comparison of Electromagnetic Performance of 10-MW Superconducting Generators With Different Topologies for Offshore Direct-Drive Wind Turbines. IEEE Transactions on Applied Superconductivity, 27(7), 1-11. https://doi.org/10.1109/tasc.2017.2732289

This paper compares the electromagnetic performance of 10MW superconducting (SC) generators with three different topologies, i.e., iron-cored stator and rotor (ISIRT), iron-cored stator and air-cored rotor (ISART), and air-cored stator and rotor (ASA... Read More about Comparison of Electromagnetic Performance of 10-MW Superconducting Generators With Different Topologies for Offshore Direct-Drive Wind Turbines.

Influence of pole number and stator outer diameter on volume, weight and cost of superconducting generator with iron-cored rotor topology for wind turbines. (2017)
Journal Article
Guan, Y., Zhu, Z. Q., Li, G.-J., Azar, Z., Thomas, A. S., Vedreño-Santos, F., & Odavic, M. (2017). Influence of pole number and stator outer diameter on volume, weight and cost of superconducting generator with iron-cored rotor topology for wind turbines. IEEE Transactions on Applied Superconductivity, 27(6), 1-9. https://doi.org/10.1109/TASC.2017.2716818

This paper investigates the influence of pole number and stator outer diameter on the performance of superconducting (SC) generators. The SC generator has an iron-cored rotor topology. Firstly, the generator structure is introduced and the optimizati... Read More about Influence of pole number and stator outer diameter on volume, weight and cost of superconducting generator with iron-cored rotor topology for wind turbines..

Comparison of Peak Armature and Field Winding Currents for Different Topologies of 10-MW Superconducting Generators Under Short-Circuit Conditions (2016)
Journal Article
Guan, Y., Vedreno-Santos, F., Li, G. J., Azar, Z., Thomas, A. S., Li, G.-J., Odavic, M., & Zhu, Z. Q. (2016). Comparison of Peak Armature and Field Winding Currents for Different Topologies of 10-MW Superconducting Generators Under Short-Circuit Conditions. IEEE Transactions on Applied Superconductivity, 26(8), 1-7. https://doi.org/10.1109/tasc.2016.2615077

This paper studies the peak armature and peak field winding currents for three different topologies of 10 MW partial High Temperature Superconducting Generators (HTSGs) under Short-Circuit Conditions (SCC) by simulation. The investigated partial HTSG... Read More about Comparison of Peak Armature and Field Winding Currents for Different Topologies of 10-MW Superconducting Generators Under Short-Circuit Conditions.

Transient diagnosis of induction generators via atom-based time-frequency transforms (2014)
Presentation / Conference Contribution
Pons-Llinares, J., Riera-Guasp, M., Antonino-Daviu, J. A., & Vedreno-Santos, F. (2014, September). Transient diagnosis of induction generators via atom-based time-frequency transforms. Presented at 2014 International Conference on Electrical Machines (ICEM)

Induction generators used in windmills usually work in non-stationary conditions, due to the varying speed of the wind. Therefore, in order to perform its diagnosis through the stator current analysis, adequate time-frequency transforms must be used.... Read More about Transient diagnosis of induction generators via atom-based time-frequency transforms.

Diagnosis of Rotor and Stator Asymmetries in Wound-Rotor Induction Machines Under Nonstationary Operation Through the Instantaneous Frequency (2014)
Journal Article
Vedreno-Santos, F., Riera-Guasp, M., Henao, H., Pineda-Sanchez, M., & Puche-Panadero, R. (2014). Diagnosis of Rotor and Stator Asymmetries in Wound-Rotor Induction Machines Under Nonstationary Operation Through the Instantaneous Frequency. IEEE Transactions on Industrial Electronics, 61(9), 4947-4959. https://doi.org/10.1109/tie.2013.2288192

This paper proposes a methodology to improve the reliability of diagnosis of different types of faults in wound-rotor induction generators which work under variable load conditions, as in wind turbine applications; the method is based on the extracti... Read More about Diagnosis of Rotor and Stator Asymmetries in Wound-Rotor Induction Machines Under Nonstationary Operation Through the Instantaneous Frequency.

Vibration Transient Detection of Broken Rotor Bars by PSH Sidebands (2013)
Journal Article
Climente-Alarcon, V., Antonino-Daviu, J. A., Vedreno-Santos, F., & Puche-Panadero, R. (2013). Vibration Transient Detection of Broken Rotor Bars by PSH Sidebands. IEEE Transactions on Industry Applications, 49(6), 2576-2582. https://doi.org/10.1109/tia.2013.2265872

In recent years, the study of transients of induction motors for diagnosis purposes has gained strength in order to overcome some inherent problems of the classical diagnosis of such machines, which uses Fourier analysis of steady-state quantities. N... Read More about Vibration Transient Detection of Broken Rotor Bars by PSH Sidebands.

Diagnosis of induction machines under non-stationary conditions by means of the spectral filter (2013)
Presentation / Conference Contribution
Vedreno-Santos, F., Riera-Guasp, M., & Pineda-Senchez, M. (2013, August). Diagnosis of induction machines under non-stationary conditions by means of the spectral filter. Presented at 2013 9th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives (SDEMPED)

This paper introduces a new way to extract the
fault components of a signal by means of a new proposed filter
based on the Sampling Theorem and the properties of Discrete
Fourier Transform. The proposed method is able to extract
fault components... Read More about Diagnosis of induction machines under non-stationary conditions by means of the spectral filter.

Diagnosis of induction machines under non-stationary conditions: Concepts and tools (2013)
Presentation / Conference Contribution
Riera-Guasp, M., Pons-Llinares, J., Climente-Alarcon, V., Vedreno-Santos, F., Pineda-Sanchez, M., Antonino-Daviu, J., Puche-Panadero, R., Perez-Cruz, J., & Roger-Folch, J. (2013, March). Diagnosis of induction machines under non-stationary conditions: Concepts and tools. Presented at 2013 IEEE Workshop on Electrical Machines Design, Control and Diagnosis (WEMDCD)

This paper is focused on fault diagnostic
methodologies suited for induction machines which are
subjected to fluctuating loads and speeds during their normal
duty cycle. In these cases, the load and speed fluctuate
continuously, near their rated... Read More about Diagnosis of induction machines under non-stationary conditions: Concepts and tools.

Diagnosis of eccentricity in induction machines working under fluctuating load conditions, through the instantaneous frequency (2012)
Presentation / Conference Contribution
Vedreno-Santos, F., Riera-Guasp, M., Henao, H., Pineda-Sanchez, M., & Antonino-Daviu, J. A. (2012, October). Diagnosis of eccentricity in induction machines working under fluctuating load conditions, through the instantaneous frequency. Presented at IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society

This paper introduces a methodology for diagnosing
mixed eccentricity fault in squirrel cage induction machines
which work under variable load conditions in generator or motor
mode; the method is based on the extraction of the instantaneous
frequ... Read More about Diagnosis of eccentricity in induction machines working under fluctuating load conditions, through the instantaneous frequency.

Electric machines diagnosis techniques via transient current analysis (2012)
Presentation / Conference Contribution
Pons-Llinares, J., Climente-Alarcon, V., Vedreno-Santos, F., Antonino-Daviu, J., & Riera-Guasp, M. (2012, October). Electric machines diagnosis techniques via transient current analysis. Presented at IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society

Induction motor condition monitoring has primarily
relied on the analysis of currents during steady-state operation
through the Fast Fourier Transform (FFT). Nonetheless, this
conventional approach has many constraints, most of them
related to th... Read More about Electric machines diagnosis techniques via transient current analysis.

Vibration transient detection of broken bars by PSH sidebands (2012)
Presentation / Conference Contribution
Climente-Alarcon, V., Antonino-Daviu, J., Vedreno-Santos, F., & Puche-Panadero, R. (2012, September). Vibration transient detection of broken bars by PSH sidebands. Presented at 2012 XXth International Conference on Electrical Machines

Abstract:
In recent years, the study of transients of induction motors for diagnosis purposes has gained strength in order to overcome some inherent problems of the classical diagnosis of such machines, which uses Fourier analysis of steady-state qu... Read More about Vibration transient detection of broken bars by PSH sidebands.

Diagnosis of faults in induction generators under fluctuating load conditions through the instantaneous frequency of the fault components (2012)
Presentation / Conference Contribution
Vedreno-Santos, F., Riera-Guasp, M., Henao, H., & Pineda-Sanchez, M. (2012, September). Diagnosis of faults in induction generators under fluctuating load conditions through the instantaneous frequency of the fault components. Presented at 2012 XXth International Conference on Electrical Machines

This paper introduces a methodology for
improving the reliability of diagnosis of different types of
faults in wound rotor induction generators which works under
variable load conditions; the method is based on the extraction
of the Instantaneous... Read More about Diagnosis of faults in induction generators under fluctuating load conditions through the instantaneous frequency of the fault components.