All Outputs (17)

Tribological and Anticorrosion Performance of Electroplated Zinc Based Nanocomposite Coatings (2020)
Journal Article
Klekotka, M., Zielińska, K., Stankiewicz, A., & Kuciej, M. (2020). Tribological and Anticorrosion Performance of Electroplated Zinc Based Nanocomposite Coatings. Coatings, 10(6), Article 594. https://doi.org/10.3390/coatings10060594

This paper presents the results of corrosion and tribological analysis of pure and nanocomposite zinc coatings. Coatings were electroplated using commercially available products—zinc acidic bath and a nanoparticle carrying plating additive. Electroch... Read More about Tribological and Anticorrosion Performance of Electroplated Zinc Based Nanocomposite Coatings.

Monitoring of the Critical Meniscus of Very Low Liquid Volumes Using an Optical Fiber Sensor (2020)
Journal Article
Binetti, L., Del Villar, I., Prabuddha Dissanayake, K., Stankiewicz, A., Sun, T., Grattan, K. T. V., & Alwis, L. S. M. (2020). Monitoring of the Critical Meniscus of Very Low Liquid Volumes Using an Optical Fiber Sensor. IEEE Sensors Journal, 20(20), 1223

A novel sensing system based on single mode optical fiber in reflective configuration has been developed to measure the critical meniscus height (CMH) of low volumes of liquids, which is then used to calculate the contact angle. The sensing system ha... Read More about Monitoring of the Critical Meniscus of Very Low Liquid Volumes Using an Optical Fiber Sensor.

Electrodeposition and characterisation of Ni/gelatin microgels coatings (2020)
Journal Article
Gibb, A., Vorobjovs, A., Jagoda, Z., Winiarski, J., & Stankiewicz, A. (2020). Electrodeposition and characterisation of Ni/gelatin microgels coatings. Transactions of the Institute of Metal Finishing, 98(1), 15-20. https://doi.org/10.1080/00202967.2020.16

This work focuses on implementing microgels for carrying self-healing substances in protective coatings. Ni/gelatin microgels coatings were manufactured using electroplating techniques. Microscopic analysis was carried out to establish the presence o... Read More about Electrodeposition and characterisation of Ni/gelatin microgels coatings.

Surface functionalisation by the introduction of self-healing properties into electroless Ni-P coatings (2018)
Journal Article
Stankiewicz, A., Kefallinou, Z., Mordarski, G., Jagoda, Z., & Spencer, B. (2019). Surface functionalisation by the introduction of self-healing properties into electroless Ni-P coatings. Electrochimica Acta, 297, 427-434. https://doi.org/10.1016/j.electac

Ni-P∖alginate microgels coatings, as potential metallic protective coatings with self-healing properties, were deposited by the electroless method. The alginate microgels contained nickel chloride and sodium hypophosphite. It was proven that the redu... Read More about Surface functionalisation by the introduction of self-healing properties into electroless Ni-P coatings.

Development of self-healing coatings for corrosion protection on metallic structures (2016)
Journal Article
Stankiewicz, A., & Barker, M. B. (2016). Development of self-healing coatings for corrosion protection on metallic structures. Smart Materials and Structures, 25(8), 084013. https://doi.org/10.1088/0964-1726/25/8/084013

Inspired by biological systems, artificial self-healing materials are designed for repairing local damage caused by external factors. The rapidly expanding field of self-healing systems contains, among others, materials with well-defined surface prop... Read More about Development of self-healing coatings for corrosion protection on metallic structures.

Gelatin microgels as a potential corrosion inhibitor carriers for self-healing coatings: Preparation and codeposition: Gelatin microgels as carriers for self-healing coatings (2015)
Journal Article
Stankiewicz, A., Jagoda, Z., Zielińska, K., & Szczygieł, I. (2015). Gelatin microgels as a potential corrosion inhibitor carriers for self-healing coatings: Preparation and codeposition: Gelatin microgels as carriers for self-healing coatings. Materials

Co-deposition of a coating with capsules containing a corrosion inhibitor is one of the methods to protect the material surface against corrosion. This generation of coatings can be regenerated in response to mechanical or chemical damage. The paper... Read More about Gelatin microgels as a potential corrosion inhibitor carriers for self-healing coatings: Preparation and codeposition: Gelatin microgels as carriers for self-healing coatings.

Machine Vision System for Corrosion Detection as an Additional Tool beside EIS for Evaluation of Protective Properties of Electrolessly Deposited Ni-P Coatings (2015)
Journal Article
Stankiewicz, A., Stankiewicz, M., Winiarski, J., Szczygieł, I., & Szczygieł, B. (2015). Machine Vision System for Corrosion Detection as an Additional Tool beside EIS for Evaluation of Protective Properties of Electrolessly Deposited Ni-P Coatings. Soli

The electroless deposition technique was used to obtain Ni-P coatings with various phosphorus content. Machine vision method was applied as a tool for the analysis and interpretation of the data provided by electrochemical impedance spectroscopy (EIS... Read More about Machine Vision System for Corrosion Detection as an Additional Tool beside EIS for Evaluation of Protective Properties of Electrolessly Deposited Ni-P Coatings.

Corrosion resistance evaluation of Ni-P\nano-ZrO 2 composite coatings by electrochemical impedance spectroscopy and machine vision method : Corrosion resistance evaluation by EIS and machine vision (2014)
Journal Article
Stankiewicz, A., Winiarski, J., Stankiewicz, M., Szczygieł, I., & Szczygieł, B. (2015). Corrosion resistance evaluation of Ni-P\nano-ZrO 2 composite coatings by electrochemical impedance spectroscopy and machine vision method : Corrosion resistance eval

Ni-P\nano-ZrO2 composite coatings were obtained on the AISI 304 steel substrate by the electroless method from a bath containing dodecyltrimethylammonium bromide (DTAB). This cationic surfactant prevents ZrO2 agglomeration in the bath and affects the... Read More about Corrosion resistance evaluation of Ni-P\nano-ZrO 2 composite coatings by electrochemical impedance spectroscopy and machine vision method : Corrosion resistance evaluation by EIS and machine vision.

Corrosion resistance of Ni-P\CePO 4 coatings obtained from sol solutions : Corrosion resistance of Ni-P\CePO 4 coatings (2014)
Journal Article
Winiarski, J., Gałuszka, M., & Stankiewicz, A. (2015). Corrosion resistance of Ni-P\CePO 4 coatings obtained from sol solutions : Corrosion resistance of Ni-P\CePO 4 coatings. Materials and corrosion : with International Corrosion abstracts = Werkstoffe und Korrosion : Organ der Arbeitsgemeinschaft Korrosion und der Dechema-Beratungsstelle für Werkstoff-Fragen, 66(6), 557-561. https://doi.org/10.1002/maco.201307570

Combined sol–gel and electroless plating techniques were used to obtain nickel-matrix composite coatings. Scanning electron microscopy (SEM) was used to examine the surface morphology. Energy dispersive spectroscopy (EDS) was employed to analyze the... Read More about Corrosion resistance of Ni-P\CePO 4 coatings obtained from sol solutions : Corrosion resistance of Ni-P\CePO 4 coatings.

Summary of Existing Models of the Ni-P Coating Electroless Deposition Process: MODELS OF THE NI-P COATING ELECTROLESS DEPOSITION PROCESS (2013)
Journal Article
Stankiewicz, A., Szczygieł, I., & Szczygieł, B. (2013). Summary of Existing Models of the Ni-P Coating Electroless Deposition Process: MODELS OF THE NI-P COATING ELECTROLESS DEPOSITION PROCESS. International Journal of Chemical Kinetics, 45(11), 755-762. https://doi.org/10.1002/kin.20810

Electroless nickel-phosphorous plating is a technique often employed in preparation of protective, decorative, and functional coatings. Several feasible mechanisms are discussed in the literature. The influence of process parameters on metal coating... Read More about Summary of Existing Models of the Ni-P Coating Electroless Deposition Process: MODELS OF THE NI-P COATING ELECTROLESS DEPOSITION PROCESS.

Self-healing coatings in anti-corrosion applications (2013)
Journal Article
Stankiewicz, A., Szczygieł, I., & Szczygieł, B. (2013). Self-healing coatings in anti-corrosion applications. Journal of Materials Science, 48(23), 8041-8051. https://doi.org/10.1007/s10853-013-7616-y

Nonmetallic (based on polymers or oxides) and metallic protective coatings are used to protect metal products against the harmful action of the corrosion environment. In recent years, self-healing coatings have been the subject of increasing interest... Read More about Self-healing coatings in anti-corrosion applications.

Impedance spectroscopy studies of electroless Ni-P matrix, Ni-W-P, Ni-P-ZrO 2 , and Ni-W-P-ZrO 2 coatings exposed to 3.5% NaCl solution : Impedance spectroscopy studies (2012)
Journal Article
Stankiewicz, A., Masalski, J., & Szczygieł, B. (2013). Impedance spectroscopy studies of electroless Ni-P matrix, Ni-W-P, Ni-P-ZrO 2 , and Ni-W-P-ZrO 2 coatings exposed to 3.5% NaCl solution : Impedance spectroscopy studies. Materials and corrosion : wit

Ni–P matrix, ternary Ni–W–P and Ni–P–ZrO2 coatings, and quaternary Ni–W–P–ZrO2 coatings were deposited using electroless method from a glycine bath. Their corrosion resistance was evaluated by electrochemical impedance spectroscopy (EIS) for various... Read More about Impedance spectroscopy studies of electroless Ni-P matrix, Ni-W-P, Ni-P-ZrO 2 , and Ni-W-P-ZrO 2 coatings exposed to 3.5% NaCl solution : Impedance spectroscopy studies.

Electroless deposition of Ni–P–nano-ZrO2 composite coatings in the presence of various types of surfactants (2012)
Journal Article
Zielińska, K., Stankiewicz, A., & Szczygieł, I. (2012). Electroless deposition of Ni–P–nano-ZrO2 composite coatings in the presence of various types of surfactants. Journal of Colloid and Interface Science, 377(1), 362-367. https://doi.org/10.1016/j.jcis.2012.03.049

Ni–P–nano-ZrO2 coatings were produced using the electroless deposition technique. To prevent agglomeration of zirconia nanoparticles in the plating bath, various surfactant additives (anionic, cationic, and nonionic) were used. The most stable bath w... Read More about Electroless deposition of Ni–P–nano-ZrO2 composite coatings in the presence of various types of surfactants.

The rate of electroless deposition of a four-component Ni–W–P–ZrO2 composite coating from a glycine bath (2009)
Journal Article
Szczygieł, B., & Turkiewicz, A. (2009). The rate of electroless deposition of a four-component Ni–W–P–ZrO2 composite coating from a glycine bath. Applied Surface Science, 255(20), 8414-8418. https://doi.org/10.1016/j.apsusc.2009.05.145

Four-component Ni–W–P–ZrO2 composite coatings were electroless deposited. A bath containing aminoacetic acid as the agent complexing nickel ions, and sodium tungstate(VI) as the source of tungstate was used. It has been determined that as the bath's... Read More about The rate of electroless deposition of a four-component Ni–W–P–ZrO2 composite coating from a glycine bath.

The effect of suspension bath composition on the composition, topography and structure of electrolessly deposited composite four-component Ni–W–P–ZrO2 coatings (2008)
Journal Article
Szczygieł, B., & Turkiewicz, A. (2008). The effect of suspension bath composition on the composition, topography and structure of electrolessly deposited composite four-component Ni–W–P–ZrO2 coatings. Applied Surface Science, 254(22), 7410-7416. ht

Composite four-component Ni–W–P–ZrO2 coatings were electrolessly deposited from a bath with different concentrations of aminoacetic acid (glycine—the complexing agent), sodium tungstate(VI) and zirconium(IV) oxide at different pH values. Concentratio... Read More about The effect of suspension bath composition on the composition, topography and structure of electrolessly deposited composite four-component Ni–W–P–ZrO2 coatings.

Surface morphology and structure of Ni–P, Ni–P–ZrO2, Ni–W–P, Ni–W–P–ZrO2 coatings deposited by electroless method (2007)
Journal Article
Szczygieł, B., Turkiewicz, A., & Serafińczuk, J. (2008). Surface morphology and structure of Ni–P, Ni–P–ZrO2, Ni–W–P, Ni–W–P–ZrO2 coatings deposited by electroless method. Surface and Coatings Technology, 202(9), 1904-1910. https://doi.org/10.1016/j.surfcoat.2007.08.016

Electroless binary Ni–P and ternary Ni–W–P alloy coatings and electroless composite (Ni–P–ZrO2 and Ni–P–W–ZrO2) nickel coatings were deposited. Baths with aminoacetic acid as the complexing agent were used. ICP measurements showed that the P content... Read More about Surface morphology and structure of Ni–P, Ni–P–ZrO2, Ni–W–P, Ni–W–P–ZrO2 coatings deposited by electroless method.

Aminoacetic acid as complexing agent in baths for electroless deposition of Ni–W–P coatings (2006)
Journal Article
Szczygieł, B., & Turkiewicz, A. (2006). Aminoacetic acid as complexing agent in baths for electroless deposition of Ni–W–P coatings. Transactions of the Institute of Metal Finishing, 84(6), 309-312. https://doi.org/10.1179/174591906x149464

Ni–W–P alloy coatings were deposited from a bath containing, nickel sulphate (VI), sodium tungstate (VI), sodium hypophosphite, sodium formate, and a complexing agent. The complexing agents were formic acid, acetic acid, lactic acid, succinic acid, m... Read More about Aminoacetic acid as complexing agent in baths for electroless deposition of Ni–W–P coatings.