All Outputs (10)

Environmental stress cracking resistance of halloysite nanoclay-polyester nanocomposites (2017)
Journal Article
Saharudin, M., Wei, J., Shyha, I., & Inam, F. (2017). Environmental stress cracking resistance of halloysite nanoclay-polyester nanocomposites. World Journal of Engineering and Technology, 5, 389-403. https://doi.org/10.4236/wjet.2017.53033

The environmental stress cracking resistance of halloysite nanoclay-polyester nanocomposites was investigated using fracture mechanics approach. The incorporation of halloysite nanoclay was found to improve the environmental stress cracking resistanc... Read More about Environmental stress cracking resistance of halloysite nanoclay-polyester nanocomposites.

Process Optimisation for Internal Cylindrical Rough Turning of Nickel Alloy 625 Weld Overlay (2017)
Journal Article
Chan, L., Shyha, I., Dreyer, D., Hamilton, J., & Hackney, P. (2017). Process Optimisation for Internal Cylindrical Rough Turning of Nickel Alloy 625 Weld Overlay. International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering, 11(4),

Nickel-based superalloys are generally known to be difficult to cut due to their strength, low thermal conductivity, and high work hardening tendency. Superalloy such as alloy 625 is often used in the oil and gas industry as a surfacing material to p... Read More about Process Optimisation for Internal Cylindrical Rough Turning of Nickel Alloy 625 Weld Overlay.

Tool Life Analysis When Turning Ti-6Al-4V Using Vegetable oil-based Cutting Fluid (2017)
Book Chapter
Gariani, S., Shyha, I., Jackson, C., & Inam, F. (2017). Tool Life Analysis When Turning Ti-6Al-4V Using Vegetable oil-based Cutting Fluid. In S. Debnath (Ed.), Manufacturing Sciences and Technologies VII (36-40). Trans Tech Publications

This paper details experimental results when turning Ti-6Al-4V using water-miscible vegetable oil-based cutting fluid. The effects of coolant concentration and working conditions on tool flank wear and tool life were evaluated. L27 fractional factori... Read More about Tool Life Analysis When Turning Ti-6Al-4V Using Vegetable oil-based Cutting Fluid.

Experimental Analysis of System Parameters for Minimum Cutting Fluid Consumption when Machining Ti-6Al-4V Using a Novel Supply System (2017)
Journal Article
Gariani, S., Shyha, I., Inam, F., & Huo, D. (2018). Experimental Analysis of System Parameters for Minimum Cutting Fluid Consumption when Machining Ti-6Al-4V Using a Novel Supply System. International Journal of Advanced Manufacturing Technology, 95, 2795-2809. https://doi.org/10.1007/s00170-017-1216-y

This paper presents the development of a new controlled cutting fluid impinging supply system (Cut-list) to deliver an accurate quantity of cutting fluid into machining zones through precisely oriented coherent round nozzles. The performance of the n... Read More about Experimental Analysis of System Parameters for Minimum Cutting Fluid Consumption when Machining Ti-6Al-4V Using a Novel Supply System.

Biodegradation of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Short Term Seawater Immersion (2017)
Journal Article
Saharudin, M., Wei, J., Shyha, I., & Inam, F. (2017). Biodegradation of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Short Term Seawater Immersion. Polymers, 9(12), Article 314. https://doi.org/10.3390/polym9080314

Halloysite nanotubes (HNTs)-polyester nanocomposites with four different concentrations were produced using solution casting technique and the biodegradation effect of short-term seawater exposure (120 h) was studied. Monolithic polyester was observe... Read More about Biodegradation of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Short Term Seawater Immersion.

Composite machining tool (2017)
Patent
Shyha, I. (2017). Composite machining tool. WO2017098242A1

Evaluation of a Novel Controlled Cutting Fluid Impinging Supply System When Machining Titanium Alloys (2017)
Journal Article
Gariani, S., Shyha, I., Inam, F., & Huo, D. (2017). Evaluation of a Novel Controlled Cutting Fluid Impinging Supply System When Machining Titanium Alloys. Applied Sciences, 7(6), Article 560. https://doi.org/10.3390/app7060560

Following a comprehensive review on titanium machining and methods of cutting fluid application, this paper presents a new Controlled cutting fluid impinging supply system (Cut‐list) developed to deliver an accurate amount of cutting fluid into the m... Read More about Evaluation of a Novel Controlled Cutting Fluid Impinging Supply System When Machining Titanium Alloys.

Flexural Properties of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Aggressive Environment (2017)
Journal Article
Saharudin, M., Wei, J., Shyha, I., & Inam, F. (2017). Flexural Properties of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Aggressive Environment. International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering, 11(4), https://doi.org/10.5281/zenodo.1129926

This study aimed to investigate the effect of aggressive environment on the flexural properties of halloysite nanotubes-polyester nanocomposites. Results showed that the addition of halloysite nanotubes into polyester matrix was found to improve flex... Read More about Flexural Properties of Halloysite Nanotubes-Polyester Nanocomposites Exposed to Aggressive Environment.

An Investigation into the Dependency of Cutting Forces on the Volume Fraction and Fibre Orientation during Machining Composite Materials (2017)
Journal Article
Kahwash, F., Shyha, I., & Maheri, A. (2017). An Investigation into the Dependency of Cutting Forces on the Volume Fraction and Fibre Orientation during Machining Composite Materials. Materials Science Forum, 882, 61-65. https://doi.org/10.4028/www.scientific.net/MSF.882.61

This paper presents an empirical force model quantifying the effect of fibre volume fraction and fibre orientation on the cutting forces during orthogonal cutting of unidirectional composites. Glass fibre plates and high speed steel cutting tools are... Read More about An Investigation into the Dependency of Cutting Forces on the Volume Fraction and Fibre Orientation during Machining Composite Materials.

Meshfree formulation for modelling of orthogonal cutting of composites (2017)
Journal Article
Kahwash, F., Shyha, I., & Maheri, A. (2017). Meshfree formulation for modelling of orthogonal cutting of composites. Composite Structures, 166, 193-201. https://doi.org/10.1016/j.compstruct.2017.01.021

The Element-Free Galerkin method (EFG) is a prominent member of the meshfree methods family. In this work, EFG is utilised to simulate the orthogonal cutting process of unidirectional composites. The mathematical model is derived from the weak form o... Read More about Meshfree formulation for modelling of orthogonal cutting of composites.