Outputs (6)

Effect of hydrogen content on the double oxide film defects and properties of aluminium castings: A review (2018)
Journal Article
El-Sayed, M. A., Shyha, I., & Basuny, F. H. (2018). Effect of hydrogen content on the double oxide film defects and properties of aluminium castings: A review. Journal of Engineering Technology, 6, 225-244

Entrapped double oxide films are known to be the most detrimental defects in cast aluminium alloys. In addition, hydrogen dissolved in the aluminium melt was suggested to pass into the defects to expand them and cause hydrogen porosity. This paper pr... Read More about Effect of hydrogen content on the double oxide film defects and properties of aluminium castings: A review.

Comparison of cutting mechanism when machining micro and nano-particles reinforced SiC/Al metal matrix composites (2018)
Journal Article
Teng, X., Chen, W., Huo, D., Shyha, I., & Lin, C. (2018). Comparison of cutting mechanism when machining micro and nano-particles reinforced SiC/Al metal matrix composites. Composite Structures, 203, 636-647. https://doi.org/10.1016/j.compstruct.2018.07.076

Recently, metal matrix composites (MMCs) reinforced with nano-particles receive increasing attention from academia and industries. The cutting mechanism of nano MMCs is believed to be different when compared to composites reinforced with micro partic... Read More about Comparison of cutting mechanism when machining micro and nano-particles reinforced SiC/Al metal matrix composites.

Dynamic simulation of machining composites using the explicit element-free Galerkin method (2018)
Journal Article
Kahwash, F., Shyha, I., & Maheri, A. (2018). Dynamic simulation of machining composites using the explicit element-free Galerkin method. Composite Structures, 198, 156-173. https://doi.org/10.1016/j.compstruct.2018.05.034

Machining operations are performed on composite parts to obtain the final geometry. However, machining composites is challenging due to their low machinability and high cost. Numerical modelling of machining presents a valuable tool for cost reductio... Read More about Dynamic simulation of machining composites using the explicit element-free Galerkin method.

Analysis of Microstructure and Chip Formation When Machining Ti-6Al-4V (2018)
Journal Article
Shyha, I., Gariani, S., El-Sayed, M., & Huo, D. (2018). Analysis of Microstructure and Chip Formation When Machining Ti-6Al-4V. Metals, 8(3), Article 185. https://doi.org/10.3390/met8030185

Microstructure and chip formation were evaluated during the step shoulder down-milling of Ti-6Al-4V using a water-miscible vegetable oil-based cutting fluid. Experiments were conducted using the Cut-list fluid supply system previous developed by the... Read More about Analysis of Microstructure and Chip Formation When Machining Ti-6Al-4V.

Finite element modelling on cutting mechanism of nano Mg/SiC metal matrix composites considering cutting edge radius (2018)
Journal Article
Teng, X., Huo, D., Chen, W., Wong, E., Zheng, L., & Shyha, I. (2018). Finite element modelling on cutting mechanism of nano Mg/SiC metal matrix composites considering cutting edge radius. Journal of Manufacturing Processes, 32, 116-126. https://doi.org/10.1016/j.jmapro.2018.02.006

In the last two decades, metal matrix composites (MMCs) have been utilised in various industrial applications owing to their high strength-to-weight ratio and superior wear resistance. However, these superior mechanical properties bring poor machinab... Read More about Finite element modelling on cutting mechanism of nano Mg/SiC metal matrix composites considering cutting edge radius.

An experimental study on tool wear behaviour in micro milling of nano Mg/Ti metal matrix composites (2018)
Journal Article
Teng, X., Huo, D., Shyha, I., Chen, W., & Wong, E. (2018). An experimental study on tool wear behaviour in micro milling of nano Mg/Ti metal matrix composites. International Journal of Advanced Manufacturing Technology, 96, 2127-2140. https://doi.org/10.1007/s00170-018-1672-z

With the development of metal matrix composites (MMCs), the mechanical properties of MMCs with a small volume fraction of nano-sized particles were found to be even superior to that with a larger content of micron-sized particles. However, the improv... Read More about An experimental study on tool wear behaviour in micro milling of nano Mg/Ti metal matrix composites.